Investigation on thermal conductivity and mechanical properties of Si3N4 ceramics via one-step sintering

High thermal conductivity Si₃N₄ ceramics were fabricated using a one-step method consisting of reaction-bonded Si₃N₄ (RBSN) and post-sintering. The influence of Si content on nitridation rate, β/(α+β) phase rate, thermal conductivity and mechanical properties was investigated in this work. It is of special interest to note that the thermal conductivity showed a tendency to increase first and then decrease with increasing Si content. This experimental result shows that the optimal thermal conductivity and fracture toughness were obtained to be 66 W (m K)^-1 and 12.0 MPa m^1/2, respectively. As a comparison, the nitridation rate and β/(α+β) phase rate in a static pressure nitriding system, i.e., 97% (MS10), 97% (MS15), 97% (MS20) and 8.3% (MS10), 8.3% (MS15), 8.9% (MS20), respectively, have obvious advantages over those in a flowing nitriding system, i.e., 91% (MS10), 91% (MS15), 93% (MS20) and 3.1% (MS10), 3.3% (MS15), 3.3% (MS20), respectively. Moreover, high lattice integrity of the β-Si₃N₄ phase was observed, which can effectively confine O atoms into the β-Si₃N₄ lattice using MgO as a sintering additive. This result indicates that one-step sintering can provide a new route to prepare Si₃N₄ ceramics with a good combination of thermal conductivity and mechanical properties.     

Gd2Zr2O7 ceramics synthesized by solid-state reactive sintering: Effects of starting powders with different-scale particle sizes

In this work, the effects of starting oxide powders with different-scale particle sizes on the synthesis of gadolinium zirconate pyrochlore (Gd₂Zr₂O₇, GZO) and its physical properties were studied. Micron Gd₂O₃ (μG), micron ZrO₂ (μZ), nano Gd₂O₃ (nG), and nano ZrO₂ (nZ) powders were used. GZO ceramics were prepared by employing solid-state reactive sintering at 1300 °C, 1400 °C, 1500 °C and 1600 °C with mixed powders of different sizes (μGμZ, μGnZ, nGμZ and nGnZ). X-ray diffraction and Raman analyses of the ceramics revealed that nG has a more significant impact on the crystallization process than nZ. All ceramics synthesized with different sized oxide powders crystallized into pyrochlore phases except for those synthesized with μGnZ mixed powders, which resulted in a fluorite phase. The results indicated that decreasing the particle size of only ZrO₂ to synthesize pyrochlore-phase Gd₂Zr₂O₇ with high crystallinity may not be effective. Samples obtained at 1500 °C were further analyzed. Scanning electron microscopy results revealed that all four ceramics have a non-homogeneous grain size and that the average grain size ranges from 5.40 to 8.30 μm. In addition, the density and Vickers hardness measurements showed that the use of nanopowders significantly improves the mechanical properties.     

Novel process for synthesizing fused mullite from titanium-rich medium/low grade or waste bauxite

This paper introduces a novel process to efficiently utilize medium-/low-grade or waste bauxite. The medium-/low-grade or waste bauxite is usually rich in iron oxide (total iron oxide content≥8%) or titanium dioxide (titanium dioxide content≥5%). In addition, both iron oxide and titanium dioxide have higher contents than typical bauxite (total iron oxide + titanium dioxide contents≥20%). It is difficult to obtain mullite with excellent properties using the process of beneficiation and sintering synthesis. Based on different reduction temperatures of K₂O, Na₂O, FeO_x, SiO₂ and TiO₂, the reduction of K₂O, Na₂O and FeO_x was set as the reduction end point. While SiO₂ start to be reduced, TiO₂ was unstable under high temperature and low oxygen partial pressure. The reason for the final formation of Ti₂O₃ in the TiO₂→TiO_2-x transformation process was analysed, and the morphology of the multiphase material obtained from the Ti₂O₃–3Al₂O₃·2SiO₂ solid solution was characterized. The reaction model was established.     

A comparative study on pyrolysis reactivity and gas release characteristics of biomass and coal using TG-MS analysis

Pyrolysis reactivity and gas release characteristics of biomass and coals were comparatively investigated using TG-MS. In addition, chemical compositions and structures of tested samples were determined to correlate pyrolysis gas release characteristic. It was found that pyrolysis reactivity and gaseous product release were hardly varied with pyrolysis heating rate. Furthermore, pyrolysis rates of two biomass samples were greater than those of coals, which were mainly attributed to the chemical compositions and the gaseous product evolution process. The result also showed that gaseous product release during pyrolysis process was related to the presence of different functional groups in samples.     

Tailoring Cu/Al2O3 catalysts for the catalytic pyrolysis of tomato waste

In this study, pyrolysis of tomato waste has been performed in fixed bed tubular reactor at 500 °C, both in absence and presence of Cu/Al₂O₃ catalyst. The influences of heating rate, catalyst preparation method and catalyst loading on bio-oil yields and properties were examined. According to pyrolysis experiments, the highest bio-oil yield was obtained as 30.31% with a heating rate of 100 °C/min, 5% Cu/Al₂O₃ catalyst loading ratio and co-precipitation method. Results showed that the catalysts have strong positive effect on bio-oil yields. Bio-oil quality obtained from fast catalytic pyrolysis was more favorable than that obtained from non-catalytic and slow catalytic pyrolysis.     

低阶煤颗粒-气/油泡间的诱导时间研究

为表征低阶煤颗粒-气/油泡间矿化过程的差异,通过Sutherland理论下固体颗粒进入泡沫产品的总概率(E)和浮选速率常数(k)之间关系,并结合低阶煤颗粒-气/油泡的浮选速率试验,求得了低阶煤颗粒-气/油泡间的诱导时间。浮选实验研究表明,在相同的捕收剂消耗量下低阶煤-油泡浮选产率均高于低阶煤-气泡浮选产率。诱导时间测试表明,低阶煤颗粒-油泡间的诱导时间(35 ms)要明显低于低阶煤颗粒-气泡间的诱导时间(93 ms)。上述实验结果表明,油泡表面的疏水性要强于传统浮选气泡表面的疏水性。然而,进一步利用Sutherland理论中固体颗粒进入泡沫产品的总概率和浮选速率常数之间的数学关系,并结合低阶煤颗粒-气/油泡的浮选速率试验求得的低阶煤颗粒-气/油泡间的诱导时间分别为9.67和8.46 ms,其与诱导时间测试仪分别测量的诱导时间差异很大。这主要是由于在实际浮选过程中气/油泡的上升速度分别为23.26和22.68 cm/s,其远高于2015EZ型诱导时间仪测试过程中气/油泡碰撞速度(2.0 cm/s)。因此,诱导时间理论计算表明气泡-颗粒间的碰撞速度对颗粒-气泡间的诱导时间影响很大。上述研究结果表明油泡浮选效果优于传统浮选的内在原因在于低阶煤颗粒-油泡间的诱导时间小于低阶煤颗粒-气泡间的诱导时间。     

Viscoelastic Behavior of Synthesized Liquid Soaps and Surface Activity Properties of Surfactants

In the present work, a rheological study of liquid soaps prepared from different mixture of surfactants as a function of surfactant type and concentration was performed. The curves of shear stress vs. shear rate and viscosity vs. shear rate were recorded at constant temperature, 294 ± 0.1 K. The surface activity properties were also studied. The results of the study showed that values of surface tension, γ, were in the range 31–40 mN m⁻¹ and the critical micelle concentration (CMC), was of the order 10⁻⁴ mol L⁻¹. The calculated maximum surface excess, Γ_max, varied from 2.40 to 3.66 μmol m⁻², while minimum area per molecule, A_min, varied from 41.1 (for amphoterics) to 81.4 Ų (for nonionic surfactants). The standard free energy of micellization, −29.8 and −29.3 kJ mol⁻¹ for anionic and amphoteric surfactants, respectively, were while values for nonionic surfactants varied between −31.8 and − 30.3 kJ mol⁻¹. The free energy of adsorption, was the lowest for amphoteric surfactants (−37.9 kJ mol⁻¹), followed by anionics (−40.4 kJ mol⁻¹) and nonionics (−43.34 to −46.84 kJ mol⁻¹), indicating that micellization process is spontaneous in the examined medium. The synthetized liquid soaps show pseudoplastic behavior and they achieved pipe flow. The results of this research indicate that flow behavior was affected significantly by the ionic charge of the surfactant and the ionic strength of the formulation, suggesting that the flow behavior could be changed by manipulating the choice of the surfactant and salinity. The pH value of all liquid soaps examined were weakly acidic, in the range of 5.0–6.4.     

等通道挤压纯铝的冷轧织构与组织演变

研究了冷轧形变量对等通道挤压纯铝的形变织构与显微组织的影响。结果表明：当形变量较小时，冷轧使挤压高纯铝的显微组织分布更加均匀。然而，随着形变量的增加，晶粒由等轴向纤维状转变。织构的演变规律为旋转立方织构和{111}<110>向冷轧织构（铜织构、黄铜织构和S织构）转变，同时出现了R织构。由此可见，等通道挤压变形对高纯铝的冷轧组织和织构存在一定的影响。